Interior paints, decorative plasters and textured coatings for painting walls, ceilings, partitions and other indoor surfaces.
PAINTS AND COATINGS FOR INTERIOR WORK
A wide range of products to bring your ideas to life
Materials for rooms with normal and high humidity
Tinting in thousands of colors according to RAL, NCS and other color catalogs
Quick-drying
Visually expands the space
Provides the effect of a snow-white silky canvas
Reliably covers in 2 coats
Super white matte
For dry rooms
PRAKTIK paint for ceilings
Packaging:
Water-dispersion polyacrylic for interior work
Download specifications
The product is manufactured until July 2026.
Purpose:
Paint for painting ceilings and upper wall panels inside dry rooms. The paint is ready to use.
Color:
Super white
Substrate type:
Concrete, brick, plastered, previously painted surfaces (non-glossy), gypsum board, fiberboard, and particle board.
Application method:
Consumption:
4−8 m²/kg
Gloss level:
Deep matte
Tinting:
Manual tinting is possible using water-based tinting pastes.
Purpose:
Paint for painting ceilings and upper wall panels inside dry rooms. The paint is ready to use.
Color:
Super white
Substrate type:
Concrete, brick, plastered, previously painted surfaces (non-glossy), gypsum board, fiberboard, and particle board.
Application method:
- brush
- roller
- spray gun
Consumption:
4−8 m²/kg
Gloss level:
Deep matte
Tinting:
Manual tinting is possible using water-based tinting pastes.
Composition:
Polyacrylic dispersion (latex), pigments, fillers, target additives, water.
Color:
Super white
Gloss level:
Deep matte
Consumption* per 1 layer on a smooth non-absorbent surface:
6-8m²/kg
Consumption* per 1 layer on an uneven absorbent surface:
4-6m²/kg
Density:
approx. 1.5 kg/l
Mass fraction of non-volatile substances:
55%
Drying time to degree 3**:
0.5 hours
The next layer can be applied after**:
1 hour**
Wash resistance:
Cleaning with a dry non-abrasive sponge or a soft-bristled
brush.
Substrate temperature during application:
+5 °C to 35 °C
* Material consumption depends on the quality of substrate preparation, application method, tools used, qualification of the performers
and may differ from the specified values.
** at t +20±2 °C and relative air humidity not more than 65±5%.
When the temperature decreases or humidity increases, the drying time may increase. At air temperatures below +15°C or
relative air humidity above 65%, apply the next layer no earlier than after 24 hours.
Polyacrylic dispersion (latex), pigments, fillers, target additives, water.
Color:
Super white
Gloss level:
Deep matte
Consumption* per 1 layer on a smooth non-absorbent surface:
6-8m²/kg
Consumption* per 1 layer on an uneven absorbent surface:
4-6m²/kg
Density:
approx. 1.5 kg/l
Mass fraction of non-volatile substances:
55%
Drying time to degree 3**:
0.5 hours
The next layer can be applied after**:
1 hour**
Wash resistance:
Cleaning with a dry non-abrasive sponge or a soft-bristled
brush.
Substrate temperature during application:
+5 °C to 35 °C
* Material consumption depends on the quality of substrate preparation, application method, tools used, qualification of the performers
and may differ from the specified values.
** at t +20±2 °C and relative air humidity not more than 65±5%.
When the temperature decreases or humidity increases, the drying time may increase. At air temperatures below +15°C or
relative air humidity above 65%, apply the next layer no earlier than after 24 hours.
Purpose and scope of application
Paint for painting ceilings and upper wall panels inside dry rooms. The paint can be applied to concrete, brick, fiberboard and particleboard, gypsum plasterboard, plastered, previously painted surfaces (non-glossy). For manual and machine application.
Approved for use in buildings and structures:
Paint for painting ceilings and upper wall panels inside dry rooms. The paint can be applied to concrete, brick, fiberboard and particleboard, gypsum plasterboard, plastered, previously painted surfaces (non-glossy). For manual and machine application.
Approved for use in buildings and structures:
- Type A — residential buildings and dormitories; buildings and premises of organizations for the upbringing and education, recreation and health improvement of children and youth; healthcare organizations; homes for the disabled and the elderly; sanatoriums; rest homes; indoor sports facilities; office premises with permanent presence of people in administrative buildings at industrial enterprises and other facilities of types B, V;
- type B — food industry, trade, and catering enterprises; hotels; non-food stores; communication enterprises; consumer service enterprises; cultural and entertainment facilities and other objects; administrative buildings;
- type C — industrial enterprises, auxiliary and utility rooms and structures; warehouses; garages.
Manual tinting is possible using water-based tinting pastes.
Surface Preparation
Prepare the substrate in accordance with SP 71.13330.2017. Clean the substrate of dust and dirt. Remove loose layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove sanding dust.
Level irregularities, depressions, cracks, and chips with Bergauf UNI PASTA water-dispersion filler and sand. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Pre-prime intensely absorbent surfaces to increase coating reliability and reduce paint consumption. It is recommended to use primers from the Praktik line (depending on the substrate type), as well as fillers.
Working Conditions
The surface to be painted must be dry and clean, the substrate temperature for work must be at least +5°C, the room temperature during paint application must be between +5°C and +35°C, and relative air humidity must be below 80%.
It is recommended to use paint from the same production batch to avoid differences in the shade of the finish layer.
Material Preparation
Stir the paint thoroughly. Stirring should be done with a wide, flat slat or a construction mixer at low speeds, carefully, avoiding the formation of air bubbles, for 1-3 minutes. It is not recommended to mix the material by shaking the closed can. After transportation and/or active stirring, if air bubbles appear, the paint needs to settle until they disappear.
If necessary, the paint can be diluted with water by no more than 5% by volume.
Application Technology
Apply the paint to the prepared dry, clean surface with a brush, roller, or spray gun. For rough surfaces such as textured plasters, brick, concrete blocks, and relief ceilings, it is recommended to use rollers with a pile length of 12-25 mm. For coarse surfaces such as fillers, plasters, concrete, fiberglass, and painting non-woven fabric — with a pile length of 8-12 mm. For smooth surfaces such as drywall, MDF, chipboard, architectural decor elements (architraves, moldings, ceiling cornices) — with a pile length up to 6 mm.
The paint is ready for use; for application by brush or roller, it can be diluted with water by no more than 5% if necessary. For airless spraying, dilution with water by 5-10% is allowed, nozzle 0.013-0.015", pressure 180-190 bar. The spray angle is chosen based on the area and geometric features of the surface being painted.
Application of two coats of paint is recommended.
Precautions
During work, avoid exposure to direct sunlight and high humidity conditions.
Upon completion of work, wash hands and tools thoroughly with warm water.
Prepare the substrate in accordance with SP 71.13330.2017. Clean the substrate of dust and dirt. Remove loose layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove sanding dust.
Level irregularities, depressions, cracks, and chips with Bergauf UNI PASTA water-dispersion filler and sand. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Pre-prime intensely absorbent surfaces to increase coating reliability and reduce paint consumption. It is recommended to use primers from the Praktik line (depending on the substrate type), as well as fillers.
Working Conditions
The surface to be painted must be dry and clean, the substrate temperature for work must be at least +5°C, the room temperature during paint application must be between +5°C and +35°C, and relative air humidity must be below 80%.
It is recommended to use paint from the same production batch to avoid differences in the shade of the finish layer.
Material Preparation
Stir the paint thoroughly. Stirring should be done with a wide, flat slat or a construction mixer at low speeds, carefully, avoiding the formation of air bubbles, for 1-3 minutes. It is not recommended to mix the material by shaking the closed can. After transportation and/or active stirring, if air bubbles appear, the paint needs to settle until they disappear.
If necessary, the paint can be diluted with water by no more than 5% by volume.
Application Technology
Apply the paint to the prepared dry, clean surface with a brush, roller, or spray gun. For rough surfaces such as textured plasters, brick, concrete blocks, and relief ceilings, it is recommended to use rollers with a pile length of 12-25 mm. For coarse surfaces such as fillers, plasters, concrete, fiberglass, and painting non-woven fabric — with a pile length of 8-12 mm. For smooth surfaces such as drywall, MDF, chipboard, architectural decor elements (architraves, moldings, ceiling cornices) — with a pile length up to 6 mm.
The paint is ready for use; for application by brush or roller, it can be diluted with water by no more than 5% if necessary. For airless spraying, dilution with water by 5-10% is allowed, nozzle 0.013-0.015", pressure 180-190 bar. The spray angle is chosen based on the area and geometric features of the surface being painted.
Application of two coats of paint is recommended.
Precautions
During work, avoid exposure to direct sunlight and high humidity conditions.
Upon completion of work, wash hands and tools thoroughly with warm water.
Storage and Transportation Conditions
Store and transport in tightly closed containers at temperatures not less than +5° and not more than +35°C. Five-fold freezing is allowed for a total duration of no more than 2 weeks at temperatures not lower than -40°C.
Protect the bucket with the product from excessive heating and avoid storage under direct sunlight. Subject to storage conditions, the guaranteed shelf life in closed factory packaging is 24 months from the date of manufacture.
During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
Safety
The product is fire- and explosion-safe, and does not contain flammable components.
Store and transport in tightly closed containers at temperatures not less than +5° and not more than +35°C. Five-fold freezing is allowed for a total duration of no more than 2 weeks at temperatures not lower than -40°C.
Protect the bucket with the product from excessive heating and avoid storage under direct sunlight. Subject to storage conditions, the guaranteed shelf life in closed factory packaging is 24 months from the date of manufacture.
During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
Safety
The product is fire- and explosion-safe, and does not contain flammable components.