Interior paints, decorative plasters and textured coatings for painting walls, ceilings, partitions and other surfaces indoors.
PAINT AND VARNISH MATERIALS FOR INTERIOR WORKS
A wide range of products to bring your ideas to life
Materials for rooms with normal and high humidity
Tinting in thousands of colors according to Ral, NCS and other color catalogs
Hides minor wall defects
Easy and convenient to apply
Does not require a perfectly smooth prepared surface
Creates a durable textured finish
Praktik decorative "Shagreen" paint
Packaging:
Water-dispersion textured paint for interior works
Download specifications
Purpose:
Paint for decorative finishing and adding texture to surfaces inside dry rooms with moderate humidity.
Base type:
Consumption:
1.5–1.8 kg/m²
Gloss level:
Matte
Tinting:
The paint can be tinted in accordance with NCS, RAL, and other tinting systems.
Paint for decorative finishing and adding texture to surfaces inside dry rooms with moderate humidity.
Base type:
- For concrete, brick, previously puttied or plastered surfaces, and drywall panels.
- Also used for finishing previously painted surfaces with water-dispersion paints that are firmly held (after preliminary sanding).
- Brush
- Roller
- Spray gun
Consumption:
1.5–1.8 kg/m²
Gloss level:
Matte
Tinting:
The paint can be tinted in accordance with NCS, RAL, and other tinting systems.
Composition:
Copolymer dispersion, fillers, thickeners, functional additives, water.
Color:
White
Gloss level:
Matte
Wash resistance:
Cleaning with a dry non-abrasive sponge or a soft-bristled brush.
Density:
1.7–1.8 kg/l
Non-volatile matter content:
about 78%
Consumption* per 1 layer:
1.5-1.8 kg/m²
Thinner:
Water
Consumption*:
From 1–1.5 m²/kg
Drying time**:
up to 24 hours.
Substrate temperature during application:
from +5 °C to +35 °C
* Material consumption depends on the quality of substrate preparation, application method, tools used, the skill level of the workers, and may differ from the indicated values.
** At t (+20±2) °C and relative air humidity of no more than (65±5) %. If the temperature decreases or humidity increases, the drying time may increase.
Copolymer dispersion, fillers, thickeners, functional additives, water.
Color:
White
Gloss level:
Matte
Wash resistance:
Cleaning with a dry non-abrasive sponge or a soft-bristled brush.
Density:
1.7–1.8 kg/l
Non-volatile matter content:
about 78%
Consumption* per 1 layer:
1.5-1.8 kg/m²
Thinner:
Water
Consumption*:
From 1–1.5 m²/kg
Drying time**:
up to 24 hours.
Substrate temperature during application:
from +5 °C to +35 °C
* Material consumption depends on the quality of substrate preparation, application method, tools used, the skill level of the workers, and may differ from the indicated values.
** At t (+20±2) °C and relative air humidity of no more than (65±5) %. If the temperature decreases or humidity increases, the drying time may increase.
Area of application
Suitable for concrete, brick, previously puttied or plastered surfaces, and drywall panels.
Also used for finishing previously painted surfaces with water-dispersion paints that are firmly held (after preliminary sanding).
For use in common areas (inter-apartment corridors, stairwells, halls, and lobbies). Recommended for residential, commercial, industrial, and warehouse premises.
Suitable for manual and machine application.
Permitted for use in buildings and structures of the following types:
Suitable for concrete, brick, previously puttied or plastered surfaces, and drywall panels.
Also used for finishing previously painted surfaces with water-dispersion paints that are firmly held (after preliminary sanding).
For use in common areas (inter-apartment corridors, stairwells, halls, and lobbies). Recommended for residential, commercial, industrial, and warehouse premises.
Suitable for manual and machine application.
Permitted for use in buildings and structures of the following types:
- Type A — residential buildings and dormitories; buildings and premises of organizations for education and training, recreation and health improvement of children and youth; healthcare organizations; homes for the disabled and elderly; sanatoriums; holiday homes; indoor sports facilities; office premises with permanent human presence in administrative buildings at industrial enterprises and other facilities of types B and C.
- Type B — food industry, trade, and catering enterprises; hotels; industrial goods stores; communications enterprises; consumer service enterprises; cultural and entertainment facilities and other objects; administrative buildings.
- Type C — industrial enterprises, auxiliary and utility rooms and structures; warehouses; garages
Paint tinting can be carried out in accordance with NCS, RAL, and other tinting systems; it is permissible to add up to 5% of tinting pastes by weight of the paint.
To avoid differences in shade on a single surface, use a product with the same batch number (see on the packaging) or pre-mix materials from different batches in a 1:1 ratio. The organization performing the tinting is responsible for the result.
Depending on the application conditions and the texture of the surface being painted, actual color shades may differ slightly from those presented in the color catalog. Before use, it is necessary to perform a test application and check the dried coating for color compliance.
After adding tinting pastes, the product should be used as soon as possible to avoid changes in the properties of the tinted material during storage.
To avoid differences in shade on a single surface, use a product with the same batch number (see on the packaging) or pre-mix materials from different batches in a 1:1 ratio. The organization performing the tinting is responsible for the result.
Depending on the application conditions and the texture of the surface being painted, actual color shades may differ slightly from those presented in the color catalog. Before use, it is necessary to perform a test application and check the dried coating for color compliance.
After adding tinting pastes, the product should be used as soon as possible to avoid changes in the properties of the tinted material during storage.
Surface preparation
Prepare the surface in accordance with SP 71.13330.2017. Clean the surface of dust and dirt. Remove loose layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte finish and remove sanding dust.
Level out irregularities, depressions, cracks, and chips with water-dispersion putty and sand them down. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Intensively absorbent surfaces should be primed beforehand to increase coating reliability and reduce paint consumption. For manual application, to improve adhesion to low-absorbent and smooth mineral surfaces, it is recommended to use Bergauf Facade Grunt adhesion primer.
It is recommended to use primers from the Praktik line (depending on the type of surface), as well as putties.
Work procedure
The surface to be painted must be dry and clean. The temperature of the surface and the environment for paint application should be from +5 °C to +35 °C, with a relative air humidity of (65±5)%. When performing work, avoid exposure to direct sunlight, high humidity conditions, and precipitation.
Stir the paint thoroughly before use. To avoid differences in shade on a single surface, use a product with the same batch number (see packaging) or pre-mix materials from different batches in a 1:1 ratio.
Depending on the application conditions and the texture of the painted surface, actual color shades may differ slightly from the reference ones. Before use, perform a test application and check the dried coating for compliance with the desired color.
Application technology
Apply the paint with a brush, roller, or hopper gun in 1 layer onto the prepared surface. Parameters for spray application: for paint with a particle size of 0.5 mm – 1.0 mm, use a pressure of 3 atm and a nozzle diameter of 4 mm. More precise parameters are determined by test painting at the site.
Prepare the surface in accordance with SP 71.13330.2017. Clean the surface of dust and dirt. Remove loose layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte finish and remove sanding dust.
Level out irregularities, depressions, cracks, and chips with water-dispersion putty and sand them down. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Intensively absorbent surfaces should be primed beforehand to increase coating reliability and reduce paint consumption. For manual application, to improve adhesion to low-absorbent and smooth mineral surfaces, it is recommended to use Bergauf Facade Grunt adhesion primer.
It is recommended to use primers from the Praktik line (depending on the type of surface), as well as putties.
Work procedure
The surface to be painted must be dry and clean. The temperature of the surface and the environment for paint application should be from +5 °C to +35 °C, with a relative air humidity of (65±5)%. When performing work, avoid exposure to direct sunlight, high humidity conditions, and precipitation.
Stir the paint thoroughly before use. To avoid differences in shade on a single surface, use a product with the same batch number (see packaging) or pre-mix materials from different batches in a 1:1 ratio.
Depending on the application conditions and the texture of the painted surface, actual color shades may differ slightly from the reference ones. Before use, perform a test application and check the dried coating for compliance with the desired color.
Application technology
Apply the paint with a brush, roller, or hopper gun in 1 layer onto the prepared surface. Parameters for spray application: for paint with a particle size of 0.5 mm – 1.0 mm, use a pressure of 3 atm and a nozzle diameter of 4 mm. More precise parameters are determined by test painting at the site.
Storage and transportation conditions
Store and transport in a tightly closed container at a temperature of not less than +5° and not more than +35°C. Five-fold freezing with a total duration of no more than 2 weeks at a temperature not lower than -40°C is allowed.
The bucket with the product should be protected from excessive heating and stored away from direct sunlight. Subject to the conditions, the guaranteed shelf life in a sealed factory packaging is 12 months from the date of manufacture.
During storage, the product may separate, which is easily corrected by stirring. Keep the partially used product in a tightly closed container and use it as soon as possible.
Safety
The product is fire and explosion-proof, does not contain flammable components.
Store and transport in a tightly closed container at a temperature of not less than +5° and not more than +35°C. Five-fold freezing with a total duration of no more than 2 weeks at a temperature not lower than -40°C is allowed.
The bucket with the product should be protected from excessive heating and stored away from direct sunlight. Subject to the conditions, the guaranteed shelf life in a sealed factory packaging is 12 months from the date of manufacture.
During storage, the product may separate, which is easily corrected by stirring. Keep the partially used product in a tightly closed container and use it as soon as possible.
Safety
The product is fire and explosion-proof, does not contain flammable components.