Interior paints, decorative plasters and textured coatings for painting walls, ceilings, partitions and other surfaces indoors.
PAINT AND VARNISH MATERIALS FOR INTERIOR WORKS
A wide range of products to bring your ideas to life
Materials for rooms with normal and high humidity
Tinting in thousands of colors according to Ral, NCS and other color catalogs
Quick-drying
Visually expands the space
Gives the effect of a snow-white silky canvas
Reliably covers in 2 coats
Super white matte
For dry rooms
PRAKTIK paint for ceilings
Packaging:
Water-dispersion polyacrylic paint for indoor use
Download specifications
The product is manufactured until July 2026.
Purpose:
Paint for painting ceilings and upper wall panels inside dry rooms. The paint is ready for use.
Color:
Super white
Base type:
Concrete, brick, plastered, previously painted surfaces (non-glossy), drywall, fiberboard and particle board.
Application method:
Consumption:
4−8 m²/kg
Gloss level:
Deep matte
Tinting:
Manual tinting is possible using water-based tinting pastes.
Purpose:
Paint for painting ceilings and upper wall panels inside dry rooms. The paint is ready for use.
Color:
Super white
Base type:
Concrete, brick, plastered, previously painted surfaces (non-glossy), drywall, fiberboard and particle board.
Application method:
- brush
- roller
- spray gun
Consumption:
4−8 m²/kg
Gloss level:
Deep matte
Tinting:
Manual tinting is possible using water-based tinting pastes.
Composition:
Polyacrylic dispersion (latex), pigments, fillers, functional additives, water.
Color:
Super white
Gloss level:
Deep matte
Consumption* per 1 layer on a smooth non-absorbent surface:
6-8 m²/kg
Consumption* per 1 layer on an uneven absorbent surface:
4-6 m²/kg
Density:
about 1.5 kg/l
Non-volatile matter content:
55%
Drying time to degree 3**:
0.5 hours
Next layer can be applied after**:
1 hour**
Wash resistance:
Cleaning with a dry non-abrasive sponge or a brush with soft
bristles.
Base temperature during application:
+5 °C to 35 °C
* Material consumption depends on the quality of surface preparation, application method, tools used, the skill of the workers
and may differ from the indicated values.
** at t +20±2 °C and relative humidity of no more than 65±5%.
If the temperature decreases or humidity increases, the drying time may increase. At an air temperature below +15°C or
relative air humidity above 65%, the next layer should be applied no earlier than 24 hours later.
Polyacrylic dispersion (latex), pigments, fillers, functional additives, water.
Color:
Super white
Gloss level:
Deep matte
Consumption* per 1 layer on a smooth non-absorbent surface:
6-8 m²/kg
Consumption* per 1 layer on an uneven absorbent surface:
4-6 m²/kg
Density:
about 1.5 kg/l
Non-volatile matter content:
55%
Drying time to degree 3**:
0.5 hours
Next layer can be applied after**:
1 hour**
Wash resistance:
Cleaning with a dry non-abrasive sponge or a brush with soft
bristles.
Base temperature during application:
+5 °C to 35 °C
* Material consumption depends on the quality of surface preparation, application method, tools used, the skill of the workers
and may differ from the indicated values.
** at t +20±2 °C and relative humidity of no more than 65±5%.
If the temperature decreases or humidity increases, the drying time may increase. At an air temperature below +15°C or
relative air humidity above 65%, the next layer should be applied no earlier than 24 hours later.
Purpose and scope of application
Paint for painting ceilings and upper wall panels inside dry rooms. The paint can be applied to concrete, brick, fiberboard and chipboard panels, plasterboard, and previously painted surfaces (non-glossy). For manual and machine application.
Suitable for use in buildings and structures:
Paint for painting ceilings and upper wall panels inside dry rooms. The paint can be applied to concrete, brick, fiberboard and chipboard panels, plasterboard, and previously painted surfaces (non-glossy). For manual and machine application.
Suitable for use in buildings and structures:
- type A — residential buildings and dormitories; buildings and premises of organizations for education and training, recreation and health improvement of children and youth; healthcare organizations; homes for the disabled and elderly; sanatoriums; holiday homes; indoor sports facilities; office premises with permanent human presence in administrative buildings at industrial enterprises and other objects of types B, C;
- type B — food industry enterprises, trade and catering; hotels; industrial goods stores; communications enterprises; consumer service enterprises; cultural and entertainment facilities and other objects; administrative buildings;
- Type C — industrial enterprises, auxiliary and utility rooms and structures; warehouses; garages.
Manual tinting is possible using water-based tinting pastes.
Surface preparation
Prepare the surface in accordance with SP 71.13330.2017. Clean the surface of dust and dirt. Remove loose layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte finish, and remove sanding dust.
Level out irregularities, depressions, cracks, and chips with Bergauf UNI PASTA water-dispersion putty, then sand. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Prime highly absorbent surfaces beforehand to increase coating reliability and reduce paint consumption. It is recommended to use primers from the Praktik line (depending on the type of surface), as well as putties.
Working conditions
The surface to be painted must be dry and clean, the surface temperature for work should be at least +5°C, the room temperature during paint application should be from +5°C to +35°C, and the relative air humidity should be below 80%.
It is recommended to use paint from the same production batch to avoid differences in the shade of the final layer.
Material preparation
Stir the paint thoroughly. It is necessary to stir with a wide, flat stick or a construction mixer at low speeds, carefully, avoiding the formation of air bubbles, for 1-3 minutes. It is not recommended to mix the material by shaking the closed container. After transportation and/or active mixing, if air bubbles appear, the paint needs to settle until they disappear.
If necessary, the paint can be diluted with water by no more than 5% by volume.
Application technology
Apply the paint to a prepared, dry, clean surface with a brush, roller, or spray gun. For rough surfaces such as textured plasters, brick, concrete blocks, and embossed ceilings, it is recommended to use rollers with a pile length of 12-25 mm. For rough surfaces such as putties, plasters, concrete, glass fiber, and painting fleece, use a pile length of 8-12 mm. For smooth surfaces such as drywall, MDF, chipboard, and architectural decor elements (architraves, moldings, ceiling cornices), use a pile length of up to 6 mm.
The paint is ready for use; for brush or roller application, it can be diluted with water by no more than 5% if necessary. For airless spraying, dilution with water by 5-10% is allowed, nozzle 0.013-0.015", pressure 180-190 bar. The spray angle is chosen based on the area and geometric features of the surface being painted.
It is recommended to apply two layers of paint.
Precautions
When working, avoid exposure to direct sunlight and high humidity conditions.
After finishing work, wash hands and tools thoroughly with warm water.
Prepare the surface in accordance with SP 71.13330.2017. Clean the surface of dust and dirt. Remove loose layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte finish, and remove sanding dust.
Level out irregularities, depressions, cracks, and chips with Bergauf UNI PASTA water-dispersion putty, then sand. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Prime highly absorbent surfaces beforehand to increase coating reliability and reduce paint consumption. It is recommended to use primers from the Praktik line (depending on the type of surface), as well as putties.
Working conditions
The surface to be painted must be dry and clean, the surface temperature for work should be at least +5°C, the room temperature during paint application should be from +5°C to +35°C, and the relative air humidity should be below 80%.
It is recommended to use paint from the same production batch to avoid differences in the shade of the final layer.
Material preparation
Stir the paint thoroughly. It is necessary to stir with a wide, flat stick or a construction mixer at low speeds, carefully, avoiding the formation of air bubbles, for 1-3 minutes. It is not recommended to mix the material by shaking the closed container. After transportation and/or active mixing, if air bubbles appear, the paint needs to settle until they disappear.
If necessary, the paint can be diluted with water by no more than 5% by volume.
Application technology
Apply the paint to a prepared, dry, clean surface with a brush, roller, or spray gun. For rough surfaces such as textured plasters, brick, concrete blocks, and embossed ceilings, it is recommended to use rollers with a pile length of 12-25 mm. For rough surfaces such as putties, plasters, concrete, glass fiber, and painting fleece, use a pile length of 8-12 mm. For smooth surfaces such as drywall, MDF, chipboard, and architectural decor elements (architraves, moldings, ceiling cornices), use a pile length of up to 6 mm.
The paint is ready for use; for brush or roller application, it can be diluted with water by no more than 5% if necessary. For airless spraying, dilution with water by 5-10% is allowed, nozzle 0.013-0.015", pressure 180-190 bar. The spray angle is chosen based on the area and geometric features of the surface being painted.
It is recommended to apply two layers of paint.
Precautions
When working, avoid exposure to direct sunlight and high humidity conditions.
After finishing work, wash hands and tools thoroughly with warm water.
Storage and transportation conditions
Store and transport in a tightly closed container at a temperature of at least +5°C and no more than +35°C. Freezing up to five times for a total duration of no more than 2 weeks at temperatures not lower than -40°C is permitted.
The bucket with the product should be protected from excessive heat and stored away from direct sunlight. If conditions are met, the warranty storage period in the original sealed packaging is 24 months from the date of manufacture.
During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
Safety
The product is fire and explosion-proof and does not contain flammable components.
Store and transport in a tightly closed container at a temperature of at least +5°C and no more than +35°C. Freezing up to five times for a total duration of no more than 2 weeks at temperatures not lower than -40°C is permitted.
The bucket with the product should be protected from excessive heat and stored away from direct sunlight. If conditions are met, the warranty storage period in the original sealed packaging is 24 months from the date of manufacture.
During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
Safety
The product is fire and explosion-proof and does not contain flammable components.