Purpose:
The paint is intended for painting mineral facades of residential and administrative buildings, as well as for walls and ceilings in rooms with normal and high humidity. It creates a coating resistant to atmospheric precipitation and biological damage.

Substrate type:
The paint can be applied to new and previously painted mineral surfaces with water-dispersion paints, plastered, puttied, concrete, brick, asbestos-cement surfaces, as well as drywall, fiberboard, and particle board exposed to atmospheric influences and used indoors. Do not use on surfaces painted with lime-silicate paints or organic elastic coatings.

Application method:

• Brush
• Roller
• Spray gun

Consumption:
8–11 m²/l

Gloss level:
Matte

Tinting:
The paint is produced in two bases, A and C, and can be tinted by computer (machine) method into colors from RAL, NCS, and other color catalogs.

Composition:
Polymer dispersion, pigments, fillers, functional additives, biocides, water.

Color:
Base A — white. Base C — transparent

Base:
A/C

Gloss level:
Matte

Consumption per 1 coat on a non-absorbent surface:
8−11 m²/kg*

Density:
Base A 1.5−1.55 kg/l
Base C 1.35−1.4 kg/l

Drying time "to touch":
1 hour**

The next coat can be applied after:
1 hour**

Wash resistance:
Wash with non-abrasive detergents, no earlier than 2 weeks after application

Water absorption GOST 33352:
less than 0.1 kg/(m2*h0.5), class W3

Vapor permeability resistance GOST 25898:
less than 0.15 m2*h*Pa/mg

Surface temperature during application:
From +5 to +35ºC

*Material consumption depends on the quality of preparation and the absorbency of the substrate, the method of application, the tools used, the qualifications of the workers, and may differ from the indicated values.
** At t (+20±2)°C and relative air humidity of no more than (65±5)%. If the temperature decreases or humidity increases, the drying time may increase. At an air temperature below +15°C or relative air humidity above 65%, the next layer should be applied no earlier than 24 hours later.

The paint is intended for painting the facades of residential and administrative buildings. The paint can be applied to surfaces made of brick, concrete, asbestos cement, as well as plastered and previously painted surfaces exposed to atmospheric influences, and can also be used indoors to obtain coatings resistant to wet cleaning and washing.

The paint can be applied to concrete, brick, fiberboard, and particle board, gypsum plasterboard, and plastered or previously painted surfaces (but not glossy ones). It is not recommended for painting plinths.
For manual and mechanized application.

The paint is produced in two bases: A (pastel colors) and C (saturated colors) and can be tinted using a computer (machine) method into RAL, NCS, and other color catalog shades. Manual tinting is possible using water-based tinting pastes. Base A can be used as a white paint; base C is used only in a tinted form.
The organization performing the tinting is responsible for the tinting result.

Depending on the application conditions and the texture of the surface being painted, the actual color shades may differ slightly from those presented in the color catalog.
Before use, it is necessary to perform a test application and check the dried coating for color compliance.
After adding tinting pastes, the product should be used as soon as possible to avoid changes in the properties of the tinted material during storage.

To avoid differences in shade, it is recommended to use a product from the same production batch on a single visual plane (the batch number is indicated on each package) or to pre-mix materials from different batches in a 1:1 ratio; the application technology must remain unchanged.

SUBSTRATE PREPARATION
Perform substrate preparation in accordance with SP 71.13330.2017.
Clean the substrate of dust and dirt. On previously painted surfaces, remove loose layers of old paint and whitewash. Sand hard and firmly adhering glossy surfaces to a matte finish, and remove sanding dust. Level out irregularities, depressions, cracks, and chips with filler Bergauf, and sand down.
Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed. Intensely absorbent surfaces should be pre-primed with Praktik strengthening primer before painting to increase coating reliability and reduce paint consumption.

WORK PROCEDURE
Stir the paint thoroughly. The paint is ready for use; if necessary, it can be diluted with water by no more than 5%. Apply the paint to a prepared, dry, and clean surface using a roller, brush, or spray gun. For rough surfaces (textured plasters, brick, concrete blocks, relief ceilings), it is recommended to use rollers with a pile length of 12–25 mm. For textured surfaces (fillers, plasters, concrete) — with a pile length of 8–12 mm. For smooth surfaces (drywall, MDF, chipboard, architectural decor elements (architraves, moldings, ceiling cornices)) — with a pile length of up to 6 mm. For airless spraying, dilution with water by 5–10% is permitted, nozzle 0.013–0.015″, pressure 180–190 bar. During work, avoid exposure to direct sunlight, high humidity conditions, and precipitation. The air and substrate temperature during application should be from +5°C to +35°C, with relative air humidity below 80%.
To obtain a saturated color and improve the appearance of the surface, two coats of paint must be applied. To avoid differences in shade, use paint from the same batch. It is recommended not to take breaks when painting a continuous surface; in areas of "overlaps," work using the "wet-on-wet" method. Work should be finished at architectural boundaries (at building corners, under downpipes, etc.).
After finishing work, wash hands and tools thoroughly with warm water.

SAFETY PRECAUTIONS
Work should be carried out using personal protective equipment for hands, eyes, and respiratory tract. Use in well-ventilated areas. In case of contact with eyes, rinse immediately with water. In case of contact with skin, wash with soap and water.

STORAGE AND TRANSPORTATION
Store and transport in a tightly closed container at a temperature from +5°C to +35°C. Five-fold freezing with a total duration of no more than 2 weeks at a temperature not lower than -40°C is allowed. The bucket with the product should be protected from excessive heat and stored away from direct sunlight. If conditions are met, the warranty shelf life in the original sealed packaging is 24 months from the date of manufacture. During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
The product is fire and explosion-proof and does not contain flammable components.

DISPOSAL
Do not pour paint products into sewage systems, water bodies, or onto the soil. Dispose of dry empty containers in accordance with local regulations; hand over liquid residues to hazardous waste collection points.