Interior paints, decorative plasters, and textured coatings for painting walls, ceilings, partitions, and other surfaces inside buildings.
PAINT AND COATING MATERIALS FOR INDOOR WORK
A wide range of products to bring your ideas to life
Materials for areas with normal and elevated humidity
Tinting in thousands of colors according to Ral, NCS and other color catalogs
Hides minor wall defects
Easy and convenient to apply
Does not require an ideally smooth, prepared surface
Creates a durable textured coating
Praktik decorative paint «Shagreen»
Packaging:
Water-dispersed textured paint for interior applications
Download specifications
Purpose:
Paint for decorative finishing and adding surface texture inside dry rooms with moderate humidity.
Substrate type:
Consumption:
1,5−1,8 kg/m²
Gloss level:
Matte
Tinting:
The paint can be tinted in accordance with NCS, RAL and other tinting systems.
Paint for decorative finishing and adding surface texture inside dry rooms with moderate humidity.
Substrate type:
- For concrete, brick, previously filled or plastered surfaces, plasterboard panels.
- It is also used for finishing previously painted surfaces that firmly adhere to water-dispersion paints (after предварительного зашкуривания).
- Brush
- Roller
- Paint sprayer
Consumption:
1,5−1,8 kg/m²
Gloss level:
Matte
Tinting:
The paint can be tinted in accordance with NCS, RAL and other tinting systems.
Composition:
Copolymer dispersion, fillers, thickeners, functional additives, water.
Color:
White
Sheen level:
Matte
Washability:
Cleaning with a dry non-abrasive sponge or brush with soft bristles.
Density:
1.7–1.8 kg/L
VOC:
about 78%
Coverage* per coat:
1.5-1.8 kg/m²
Thinner:
Water
Coverage*:
From 1–1.5 m²/kg
Drying time**:
up to 24 hours.
Surface temperature during application:
from +5 °C to +35 °C
* Coverage depends on the quality of surface preparation, application method, the tools used, the installers’ qualifications, and may differ from the stated values.
** At t (+20±2) °C and relative humidity of air no more than (65±5) %. If the temperature decreases or humidity increases, drying time may increase.
Copolymer dispersion, fillers, thickeners, functional additives, water.
Color:
White
Sheen level:
Matte
Washability:
Cleaning with a dry non-abrasive sponge or brush with soft bristles.
Density:
1.7–1.8 kg/L
VOC:
about 78%
Coverage* per coat:
1.5-1.8 kg/m²
Thinner:
Water
Coverage*:
From 1–1.5 m²/kg
Drying time**:
up to 24 hours.
Surface temperature during application:
from +5 °C to +35 °C
* Coverage depends on the quality of surface preparation, application method, the tools used, the installers’ qualifications, and may differ from the stated values.
** At t (+20±2) °C and relative humidity of air no more than (65±5) %. If the temperature decreases or humidity increases, drying time may increase.
Application area
Suitable for concrete, brick, previously filled or plastered surfaces, and plasterboard panels.
It is also used for finishing previously painted surfaces that firmly adhere to water-dispersion paints (after предварительного зашкуривания).
For use in public areas (inter-apartment corridors, stairwells, lobbies, and vestibules). Recommended for residential, commercial, industrial, and warehouse premises.
Suitable for manual and machine application.
May be used in buildings and structures of types:
Suitable for concrete, brick, previously filled or plastered surfaces, and plasterboard panels.
It is also used for finishing previously painted surfaces that firmly adhere to water-dispersion paints (after предварительного зашкуривания).
For use in public areas (inter-apartment corridors, stairwells, lobbies, and vestibules). Recommended for residential, commercial, industrial, and warehouse premises.
Suitable for manual and machine application.
May be used in buildings and structures of types:
- Type A — residential houses and dormitories; buildings and premises of organizations for upbringing and education, recreation and health improvement for children and youth; healthcare facilities; homes for persons with disabilities and the elderly; sanatoriums; holiday homes; enclosed sports facilities; service premises with people staying on a permanent basis in administrative buildings at industrial enterprises and other facilities of types B, V.
- Type Б — food industry enterprises, trade and public catering; hotels; retail stores for industrial goods; communications enterprises; consumer service enterprises; cultural, entertainment and other facilities; administrative buildings.
- Type В — industrial enterprises, auxiliary and domestic premises and structures; warehouses; garages
Paint tinting may be carried out in accordance with NCS, RAL and other tinting systems; it is permissible to add up to 5% tinting pastes by mass of the paint.
To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio. The organization performing the tinting is responsible for the tinting result.
Depending on the application conditions and the texture of the surface to be painted, the actual color shades may differ slightly from those presented in the color catalog. Before use, you must perform a test application and check the dried coating for compliance with the color.
After adding tinting pastes, the product should be used within the shortest possible time to avoid changes in the properties of the tinted material during storage.
To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio. The organization performing the tinting is responsible for the tinting result.
Depending on the application conditions and the texture of the surface to be painted, the actual color shades may differ slightly from those presented in the color catalog. Before use, you must perform a test application and check the dried coating for compliance with the color.
After adding tinting pastes, the product should be used within the shortest possible time to avoid changes in the properties of the tinted material during storage.
Surface preparation
Carry out the surface preparation in accordance with SP 71.13 330.2017. Remove dust and dirt from the substrate. From previously painted surfaces remove weak layers of old paint and limewash. Sand hard and firmly adhering glossy surfaces until a matte finish is obtained; remove dust from sanding.
Level uneven areas, depressions, cracks and chips with a water-dispersion filler, then sand them smooth. Surfaces previously coated with chalk or lime-based paints must be carefully cleaned until completely removed.
Pre-prime surfaces with high absorbency in advance to improve coating reliability and reduce paint consumption. When applying manually, to improve adhesion to low-absorbency and smooth mineral substrates, it is recommended to use Bergauf Facade Grunt adhesion primer.
It is recommended to use primers from the Praktik range (depending on the type of substrate), as well as putties.
Order of work
The surface to be painted must be dry and clean. The substrate and ambient temperature for applying the paint should be from +5 °C to +35 °C, the relative humidity of the air (65±5) %. During the work avoid exposure to direct sunlight, conditions of increased humidity and contact with atmospheric precipitation.
Thoroughly mix the paint before use. To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio.
Depending on the application conditions and the texture of the surface to be painted, the actual color shades may differ slightly from the reference ones. Before use, you must perform a test application and check the dried coating for compliance with the desired color.
Application method
Apply the paint with a brush, roller or airless spray gun in 1 coat onto the prepared surface. Parameters for spray application: for paint with a particle size of 0.5 mm — 1.0 mm pressure 3 atm, nozzle diameter 4 mm. More precise parameters are determined by trial coating on the site object.
Carry out the surface preparation in accordance with SP 71.13 330.2017. Remove dust and dirt from the substrate. From previously painted surfaces remove weak layers of old paint and limewash. Sand hard and firmly adhering glossy surfaces until a matte finish is obtained; remove dust from sanding.
Level uneven areas, depressions, cracks and chips with a water-dispersion filler, then sand them smooth. Surfaces previously coated with chalk or lime-based paints must be carefully cleaned until completely removed.
Pre-prime surfaces with high absorbency in advance to improve coating reliability and reduce paint consumption. When applying manually, to improve adhesion to low-absorbency and smooth mineral substrates, it is recommended to use Bergauf Facade Grunt adhesion primer.
It is recommended to use primers from the Praktik range (depending on the type of substrate), as well as putties.
Order of work
The surface to be painted must be dry and clean. The substrate and ambient temperature for applying the paint should be from +5 °C to +35 °C, the relative humidity of the air (65±5) %. During the work avoid exposure to direct sunlight, conditions of increased humidity and contact with atmospheric precipitation.
Thoroughly mix the paint before use. To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio.
Depending on the application conditions and the texture of the surface to be painted, the actual color shades may differ slightly from the reference ones. Before use, you must perform a test application and check the dried coating for compliance with the desired color.
Application method
Apply the paint with a brush, roller or airless spray gun in 1 coat onto the prepared surface. Parameters for spray application: for paint with a particle size of 0.5 mm — 1.0 mm pressure 3 atm, nozzle diameter 4 mm. More precise parameters are determined by trial coating on the site object.
Storage and transportation conditions
Store and transport in tightly closed containers at a temperature of not less than +5° and not more than +35°C. Up to five freeze-thaw cycles are permitted with a total duration of no more than 2 weeks at a temperature not below -40°C.
It is necessary to protect the bucket with the product from excessive heating and avoid storage in direct sunlight. If the conditions are met, the warranty storage period in a closed factory package is 12 months from the date of manufacture.
During storage, the product may separate; this can be easily eliminated by mixing. Do not keep the product that has not been fully used in a tightly closed container and use it within the shortest possible time.
Safety
The product is fire- and explosion-safe and does not contain flammable components.
Store and transport in tightly closed containers at a temperature of not less than +5° and not more than +35°C. Up to five freeze-thaw cycles are permitted with a total duration of no more than 2 weeks at a temperature not below -40°C.
It is necessary to protect the bucket with the product from excessive heating and avoid storage in direct sunlight. If the conditions are met, the warranty storage period in a closed factory package is 12 months from the date of manufacture.
During storage, the product may separate; this can be easily eliminated by mixing. Do not keep the product that has not been fully used in a tightly closed container and use it within the shortest possible time.
Safety
The product is fire- and explosion-safe and does not contain flammable components.