Purpose:
The paint is intended for painting walls and ceilings in rooms with normal and varying humidity (kitchens, dining rooms, corridors) with moderate service load, including in children's, preschool, educational, medical and preventive institutions. Forms a moisture-resistant coating, resistant to the effects of water vapour and condensation, for light damp cleaning without the use of detergents and abrasive materials. ready for use.

Substrate type:
Paint can be applied to new and previously painted plasterboard with water-dispersed paints; plastered, filled, concrete, brick, wooden plank surfaces, particle board (chipboard), fiberboard, fiberglass fabric and smooth painter's nonwoven.
For indoor use.

Application method:

• Brush
• Roller
• Paint sprayer

Consumption:
8−11 m²/kg

Gloss level:
Matte

Tinting:
Tinting of the paint can be carried out in accordance with NCS, RAL and other tinting systems.

Composition:
Polymer dispersion, pigments, fillers, functional additives, biocides, water.

Color:
Base A — white
Base C — transparent

Sheen level:
Matte

Coverage per 1 coat on a smooth, non-absorbent surface:
8−11 m²/kg

Density:
Base, A 1.55−1.6 kg/l
Base C 1.26−1.3 kg/l

Drying time «to touch"**:
1 hour

The next layer can be applied after**:
1.5 hours**

Resistance to wet abrasion GOST 32 300/ DIN EN 13 300:
Class 4

Washability:
Easy wet cleaning without using detergents

Air and surface temperature during application:
+5 °C to 35 °C

* Material consumption depends on the quality of surface preparation and the absorbency of the surface, the application method, the tool used, the skill level of the contractors and may differ from the specified values.
** At t (+20±2)°C and relative air humidity not exceeding (65±5)%. When the temperature is reduced or humidity is increased, the drying time may increase. At an air temperature below +15°C or relative air humidity above 65%, apply the next coat no earlier than after 24 hours.

Purpose and properties
The paint is intended for painting walls and ceilings in rooms with normal and varying humidity (kitchens, dining rooms, corridors) with moderate service load, including in children's, preschool, educational, and health care and preventive institutions. It forms a moisture-resistant coating that is resistant to exposure to water vapour and condensation, and to easy wet cleaning without the use of detergents and abrasive agents. It is easy to apply and roll out without splashing and drips.
Water-vapour permeable.
Economical consumption.
Tintable in pastel and saturated colors.

Scope of use
The paint can be applied to plasterboard made of new and previously painted with water-dispersed paints; plastered, filled, concrete, brick, wooden board surfaces, particle board (chipboard), fibreboard, glass fabric, and smooth wallcovering non-woven material.
For indoor use.
Dor manual and mechanized application.
Used in all types of buildings and structures (A, B, C).

The paint is supplied in two bases: A (pastel colors) and C (saturated colors) and can be computer-tinted (machine-tinted) to colors RAL, NCS and other color catalogs. Manual tinting with tinting pastes on a water-based basis is possible. Base A can be used as white paint; base C is used only in tinted form.
The organization performing the tinting is responsible for the tinting result.

Depending on the application conditions and the texture of the painted surface, the actual color shades may differ slightly from those shown in the color catalog.
Before use, perform a test application and check the dried coating for color conformity.
After adding tinting pastes, the product should be used within the shortest possible time to avoid changes in the properties of the tinted material during storage.

To avoid differences in shade, it is recommended that on one visible surface you use a product from a single production batch (batch number is indicated on each package) or pre-mix materials from different batches in a 1:1 ratio; the application technology must remain unchanged.

SURFACE PREPARATION
Prepare the surface in accordance with SP 71.13 330.2017.
Clean the surface from dust and dirt. On previously painted surfaces, remove loose layers of old paint and limewash. Sand hard and firmly adhering glossy surfaces until they become matte; remove dust from sanding. Level out unevenness, cavities, cracks and chips with putty Bergauf, sand it down.
Surfaces previously coated with chalk or lime paints must be thoroughly cleaned until completely removed. Highly absorbent surfaces should be pre-primed with a Praktik strengthening primer under paint to increase the reliability of the coating and reduce paint consumption.

WORK PROCEDURE
Thoroughly mix the paint. The paint is ready for use; if necessary, it can be diluted with water by no more than 5%. Apply the paint to the prepared, dry, clean surface using a roller, brush or paint sprayer in two coats. For rough surfaces (textured plasters, brick, concrete blocks, embossed ceilings) it is recommended to use rollers with a pile length of 12−25 mm. For rough surfaces (putty, plaster, concrete) — with a pile length of 8−12 mm. For smooth surfaces (drywall, MDF, chipboard, architectural decor elements (trim, mouldings, ceiling cornices)) — with a pile length up to 6 mm. For airless spraying, dilution with water by 5−10% is allowed; nozzle 0,013−0,015″, pressure 180−190 bar. During work, avoid exposure to direct sunlight, conditions of increased humidity and entry of atmospheric precipitation. Air and substrate temperature during application from +5°C to +35°C, relative air humidity below 80%.
After completion of work, wash hands and tools thoroughly with warm water.

SAFETY INSTRUCTIONS
The work should be carried out using personal protective equipment for hands, eyes, and respiratory protection. Use in well-ventilated premises. In case of contact with eyes, rinse immediately with water. In case of contact with skin, rinse with water and soap.

Store and transport in tightly closed containers at a temperature from +5°C to +35°C. Up to fivefold freezing with a total duration of no more than 2 weeks is allowed at a temperature not lower than -40°C. The product bucket should be protected from excessive heating and stored away from direct sunlight. If the conditions are met, the guaranteed shelf life in a closed factory package is 24 months from the date of manufacture. During storage, product separation may occur; it is easily eliminated by stirring. Do not keep the product that has not been used up completely in a tightly closed container and use it " as quickly as possible.
The product is fire- and explosion-safe and does not contain flammable components.

DISPOSAL
Do not pour paint and coating products into the sewer system, water bodies, or onto the ground. Dispose of dry, empty containers in accordance with local legislation; pass liquid residues to hazardous waste collection points.