Purpose:
The paint is intended for painting ceilings and upper wall panels inside dry rooms. The matte paint texture conceals minor surface imperfections on the ceiling. Provides high-quality, even painting, and leaves no splashes or drips. Easy to apply, dries quickly, and has no strong odor. Manual tinting is possible using water-based tinting pastes.
Creates a pure white “breathable” coating.
Visually expands the space.
Reliable coverage in 2 coats.

Color:
Super white

Type of substrate:
The paint can be applied to plasterboard, both new and previously painted with water-dispersion paints; plastered, filled, concrete, brick, chipboard, fibreboard, fiberglass mesh and smooth painting wallpaper (flizelin).
For indoor use.

Application method:

• brush
• roller
• spray gun

Consumption:
8−11 m²/kg

Gloss level:
Deep matte

Tinting:
Manual tinting using water-based tinting pastes is possible.

Composition:
Polymer dispersion, pigments, fillers, functional additives, biocides, water.

Color:
Super white

Gloss level:
Deep matte

Consumption* per 1 coat on a smooth non-absorbent surface:
8–11 m^2/l

Density:
1.5–1.55 kg/l

Drying time «to the touch»**:
0.5 hour

Time to apply the next coat**:
1 hour**

Surface temperature during application:
+5 °C to 35 °C


* Material consumption depends on the quality of surface preparation and the absorbency of the surface, the application method, the tool used, the skill level of the contractors and may differ from the specified values.
** At t (+20±2)°C and relative air humidity not exceeding (65±5)%. When the temperature is reduced or humidity is increased, the drying time may increase. At an air temperature below +15°C or relative air humidity above 65%, apply the next coat no earlier than after 24 hours.

Purpose and scope of application
The paint can be applied to plasterboard, both new and previously painted with water-dispersion paints; plastered, filled, concrete, brick, chipboard, fibreboard, fiberglass mesh and smooth painting wallpaper (flizelin).
For indoor use.
For manual and mechanized application.

Used in all types of buildings and structures (A, B, C).

Manual tinting with water-based tinting pastes is possible.

Preparing the substrate
Prepare the surface in accordance with SP 71.13 330.2017.
Clean the surface from dust and dirt. On previously painted surfaces, remove loose layers of old paint and limewash. Sand hard and firmly adhering glossy surfaces until they become matte; remove dust from sanding. Level out unevenness, pits, cracks and chips with putty Bergauf, sand until smooth.
Surfaces previously coated with chalk or lime paints must be thoroughly cleaned until completely removed. Highly absorbent surfaces should be pre-primed with a Praktik strengthening primer under paint to increase the reliability of the coating and reduce paint consumption.

Work sequence
Stir the paint thoroughly. The paint is ready to use; if necessary, it can be diluted with water by no more than 5%. Apply the paint to the prepared dry, clean surface using a roller, brush or paint sprayer in two coats. For rough surfaces (textured plasters, brick, concrete blocks, embossed ceilings), it is recommended to use rollers with a pile length of 12−25 mm. For rough surfaces (filler, plaster, concrete) — with a pile length of 8−12 mm. For smooth surfaces (plasterboard, MDF, chipboard, elements of architectural decor (trim, mouldings, ceiling cornices)) — with a pile length of up to 6 mm. For airless spraying, dilution with water of 5−10% is permitted, nozzle 0,013−0,015", pressure 180−190 bar. When carrying out work, avoid exposure to direct sunlight, conditions of high humidity, and getting atmospheric precipitation on the surface. Air and base temperature during application from +5°C to +35°C, relative air humidity below 80%.
After completing the work, wash hands and tools thoroughly with warm water.

Safety precautions
The work should be carried out using personal protective equipment for hands, eyes, and respiratory protection. Use in well-ventilated premises. In case of contact with eyes, rinse immediately with water. In case of contact with skin, rinse with water and soap.

Storage and transportation conditions
Store and transport in tightly closed containers at a temperature from +5°C to +35°C. Up to fivefold freezing with a total duration of no more than 2 weeks is allowed at a temperature not lower than -40°C. The product bucket should be protected from excessive heating and stored away from direct sunlight. If the conditions are met, the guaranteed shelf life in a closed factory package is 24 months from the date of manufacture. During storage, product separation may occur; it is easily eliminated by stirring. Do not keep the product that has not been used up completely in a tightly closed container and use it " as quickly as possible.
The product is fire- and explosion-safe and does not contain flammable components.

Disposal
Do not pour paint and coating products into the sewer system, water bodies, or onto the ground. Dispose of dry, empty containers in accordance with local legislation; pass liquid residues to hazardous waste collection points.